Paper Search Console

Home Search Page About Contact

Journal Title

Title of Journal: Int J Precis Eng Manuf

Search In Journal Title:

Abbravation: International Journal of Precision Engineering and Manufacturing

Search In Journal Abbravation:

Publisher

Korean Society for Precision Engineering

Search In Publisher:

DOI

10.1007/bf02296808

Search In DOI:

ISSN

2005-4602

Search In ISSN:
Search In Title Of Papers:

Kinetic role of the metatarsophalangeal joint in n

Authors: Youngho Kim Seunghyeon Kim Jongsang Son Bora Jeong
Publish Date: 2012/07/07
Volume: 13, Issue: 8, Pages: 1481-1485
PDF Link

Abstract

Joint moment and power of the metatarsophalangeal MP joint in normal horizontal barefoot walking were determined in this study The threedimensional motion analysis with synchronous measurements of ground reaction forces and foot pressure distribution was performed with the twosegment foot model Twentytwo adult subjects were selected for the study Compared to the previous studies results of this study showed reasonable joint moments from footflat to toeoff The MP joint angles showed a very good agreement with the previous studies The maximum MP joint moment was 013 ± 004 Nm/kg at preswing approximately onetenth of the ankle joint moment A considerable energy absorption of approximately 656 GC J/kg was found at the MP joint during 30~60 of the gait cycle This study would be beneficial to understand the mechanism of various foot diseases such as hallux valgus and plantar fasciitis

Keywords:

References

.
Search In Abstract Of Papers:
Other Papers In This Journal:
  1. Valveless piezoelectric micropump of parallel double chambers
  2. Performance of honed surface profiles to artificial hip joints: An experimental investigation
  3. Direct fabrication of nano-wrinkled 3D microstructures using fitfully accumulated two-photon polymerization
  4. Machining model of position-attitude in Magnetorheological Finishing (MRF) of high-precision off-axis aspheric optical elements
  5. Direct visual servoing framework based on optimal control for redundant joint structures
  6. Development of warm forming parts for automotive body dash panel using AZ31B magnesium alloy sheets
  7. Design optimization method for 7 DOF robot manipulator using performance indices
  8. Beam vibration control using cellulose-based Electro-Active Paper sensor
  9. Dry rotary swaging–approaches for lubricant free process design
  10. Chemical mechanical planarization of copper bumps on printed circuit board
  11. Preparation of micro-channel catalytic reactor coated with macro-porous Al 2 O 3 for fuel reformer
  12. Development of a surface-based virtual dental sculpting simulator with multimodal feedback
  13. Development of acoustic emission signal parameter and its application for strength estimation of friction welded joints
  14. Optimal product design for life cycle assessment (LCA) with the case study of universal motors
  15. From design for manufacturing (DFM) to manufacturing for design (MFD) via hybrid manufacturing and smart factory: A review and perspective of paradigm shift
  16. Molecular dynamics simulations of plastic material deformation in machining with a round cutting edge
  17. Physical simulation of small melter for LTCC (low temperature co-fired ceramic) frit
  18. NDE of low-velocity impact damages in composite laminates using ESPI, digital shearography and ultrasound C-scan techniques
  19. Development of post processor for five-axis machine of non-orthogonal head tilting type
  20. Influence of current collector and cathode area discrepancy on performance evaluation of solid oxide fuel cell with thin-film-processed cathode
  21. Research advancement of green technologies
  22. Texture evolution in low-C flat rolled steels on the physical properties
  23. Generation of velocity profiles with speed limit of each axis for high-speed machining using look-ahead buffer
  24. Comparative studies of parameters calibration for focused ion beam deposition
  25. Development of a new head/brain model for the prediction of subdural hemorrhage
  26. Prediction of heating-line paths in induction heating process using the artificial neural network
  27. Multi objective optimization of friction stir welding parameters using FEM and neural network
  28. Service reliability improvement in manufacturing and operating systems
  29. A study on the characteristics of a wafer-polishing process according to machining conditions
  30. FlipBot: A new field robotic platform for fast stair climbing
Search Result: