Paper Search Console

Home Search Page About Contact

Journal Title

Title of Journal: J Wuhan Univ TechnolMat Sci Edit

Search In Journal Title:

Abbravation: Journal of Wuhan University of Technology-Mater. Sci. Ed.

Search In Journal Abbravation:

Publisher

Wuhan University of Technology

Search In Publisher:

DOI

10.1007/978-1-4684-7493-0_50

Search In DOI:

ISSN

1993-0437

Search In ISSN:
Search In Title Of Papers:

The influence of material related parameters on th

Authors: Jinzhi Xu Peiwen Hao
Publish Date: 2014/03/08
Volume: 29, Issue: 1, Pages: 119-125
PDF Link

Abstract

By indirect tensile strength ITS test and unconfined compressive strength UCS test the influence of various material related parameters including asphalt foamability aggregate temperature mixing moisture content MMC and foamed asphalt FA content on the mechanical properties of FA mixes was studied The results indicated that both asphalt foamability and aggregate temperature greatly affected ITS of FA mixes Too low aggregate temperature was unfavorable for mechanical properties of FA mixes Foamed index alone was unfit for the evaluation of asphalt foamability Compared with halflife expansion ratio had more prominent influence on ITS of FA mixes MMC had significant impact on the mechanical properties of FA mixes and should be optimized by trial and test in FA mix design The mechanical properties of FA mix were sensitive to the change of FA content Compared with the ITS determined with standard Marshall specimens both the ITS and UCS determined with static compressed specimens by 15 cm diameter were more effective in terms of choosing the optimal asphalt content for FA mixes

Keywords:

References

.
Search In Abstract Of Papers:
Other Papers In This Journal:
  1. The synthesis technique of polyacrylic acid superplasticizer
  2. Novel MoS 2 microspheres formed by solid-state assembly of ultrathin nanosheets
  3. Structural and optical properties of Ce 3+ , Yb 3+ Co-doped YAG films by pulsed laser deposition
  4. Preparation and characterization of polylactide/montmorillonite nanocomposites
  5. Influence of mechanical behavior between the grains on stress fluctuation of aluminum alloy thick plate
  6. Influence of mechanical behavior between the grains on stress fluctuation of aluminum alloy thick plate
  7. Comparative DFT study of [Mg(CHZ) 3 ](ClO 4 ) 2 and [Mg(CHZ) 3 ](NO 3 ) 2 (CHZ=Carbohydrazide)
  8. Laser cladding Al-Si/Al 2 O 3 -TiO 2 composite coatings on AZ31B magnesium alloy
  9. The complete stress-strain curve of recycled aggregate concrete under uniaxial compression loading
  10. Porous flame-retarded asphalt pavement for highway tunnel
  11. Preparation of Ni60-Cr 3 C 2 coating by plasma spraying, plasma re-melting and plasma spray welding on W6Mo5Cr4V2
  12. MCM-41 prepared with ionic liquid and cethytrimethylammonium bromide as co-templates
  13. A novel fluorescence probe 9-(4-(1,2-diamine)benzene-N 1 -phenyl)acridine for nitric oxide determination
  14. Optical and magnetic properties of Fe 2 O 3 /SiO 2 nano-composite films
  15. Evaluation of sub-microstructure in concrete with low water-binder ratio by SEM-BSE image analysis
  16. Microwave sintering of W-15Cu ultrafine composite powder prepared by spray drying & calcining-continuous reduction technology
  17. Kinetics of synthesis of YAG nanocrystals by ultrasound and ultrasound-microwave-assisted methods
  18. Rheological properties of asphalt modified by supramolecular UV resistant material-LDHs
  19. Shape-stablized EP/paraffin composite for latent heat storage
  20. Influence of nano-SiO 2 addition on properties of sulphoaluminate cement based material
  21. Preparation and lab evaluation of a new denture adhesive
  22. Biomineralization of the surface of PLGA-(ASP-PEG) modified with the K 16 and RGD-containing peptide
  23. Non-isothermal melt crystallization kinetics of anhydrite-filled polypropylene composites
  24. Effect of ECAP on the microstructure and mechanical properties of a high-Mg 2 Si content Al-Mg-Si alloy
  25. Near-infrared quantum cutting in Pr 3+ -Yb 3+ Co-doped oxyfluoride glass ceramics containing CaF 2 nanocrystals
  26. Mesoporous bioglass/silk fibroin scaffolds as a drug delivery system: Fabrication, drug loading and release in vitro and repair calvarial defects in vivo
  27. Influence of pH on the property of apatite-type lanthanum silicates prepared by sol-gel process
  28. Analysis of aging mechanism of SBS polymer modified asphalt based on Fourier transform infrared spectrum
  29. Preparation and properties of particle reinforced Sn-Zn-based composite solder
  30. Hydrothermal synthesis ultralong single-crystal Sb 2 S 3 nanowires
  31. Effect of organophilic montmorillonite on thermal-oxidative aging behavior of SBS modified bitumen crack filling material
  32. Properties and mechanism of CFBC fly ash-cement based stabilizers for lake sludge
  33. Synthesis and applications of tetra-functional branched poly(ethylene glycol) derivative for the decellularized valve leaflets cross-linking
  34. Leaching behavior and mechanism of cement solidified heavy metal Pb in acid medium
  35. Effect of functional chemical admixtures on the performance of cement asphalt mortar used in ballastless track
  36. First-principles investigation of the structural, electronic and elastic properties of Al 2 Ca and Al 4 Sr phases in Mg-Al-Ca(Sr) alloy
  37. Effects of deformation modes on texture evolution during hot working of Al-Zn-Mg-Cu-Zr alloy
  38. Performance investigation of square concrete-filled steel tube columns
  39. Synthesis and luminescence properties of red phosphor CaO: Eu 3+
  40. The crack of harden cement paste observed with multi-technique
Search Result: